This tender with title Purchase of Drill Bit (Different size) has been published on Bidding Source portal dated 10 Jan 2024 for the country of Bangladesh. It has been categorized on Drill bits. For similar tenders you can see tenders mentioned below of this page.
General Information
Purchase of Drill Bit (Different size)
Invitation to Tender
Bangladesh
10 Jan 2024
27 Feb 2024
English
Drill bits
For viewing full details of tenders, you should Log in to your account. If not registered yet, Please Register Now
Or Request a call back now and one of our representatives will contact you. Contact us
Similar Tenders
Bangladesh - Supply of Colate, Drill bit , Insulation plate, lock bar clip, different types nut and bolt, connectors and other goods for signaling system. Bangladesh Bangladesh - GR-/5 Supply of different type of tools for machine shop (Drill bit, Milling Cutter, Diamond tips, Taps etc.); Fabrication Shop (Welding M/C, Grinding M/C, Drill M/C, Cutting Disc etc.) and Car Workshop (Wrench, Lifting Jac etc.). Bangladesh BITAC.PUR.2022-23 GR-39 Lot-03 Procurement of EDM Wire Cut and EDM Drill Machine Bangladesh 1. A) Drilling Machine Set: The Manually Operated Drilling machine will run in the field of 2D Seismic operation. Proper base fitting and other accessories are required. The machine will run about 10 hours/day (with cycle of 1 hour runtime and 15 minutes stop time). The system has to be easy portable for seismic drilling (manual) operation (in hard formation/area) (45 m depth).?5 meter Sets 56 Each Drilling Machine set includes following items with mentioned nos./set( Each parts must be Compatible with drilling machine & accessories) i) Pump with Engine:Gasoline operated engine coupled with high pressure centrifugal small, narrow type, cast iron made, capable of welding &soldering (non-aluminum) pump. Pump type:Trash Centrifugal, Self-Priming, air-cooled type, Suction diameter=75mm, delivery diameter=50mm (Approx.) Engine : Force air-cooling, 1 cylinder, 4-stroke OHV gasoline engine Output power: 7 hpor Higher (5.1 Kwh or Higher) (3600r/min) Displacement: 242 cc or Higher Rated discharge capacity: 1200 to 1500 (L/ min) Maximum Discharge Capacity: 1500 L/min Suction Head Lift: 8 m Total head lift : 27m Fuel capacity : 6L Dimensions (mm) (LxWxH): 660 x 495 x 515 (Approx.) Net Dry weight: 50 kg (? 5 kg) Set 01 ii) Swivel: Compatible with drilling pipe and delivery hosepipe. Steel made U-type swivel, outer bent, bent at the middle of the length, compatible with pump delivery hose, easy to joint by clamp with delivery hosepipe & output side compatible (easy to joint by threads) with drill pipe. The internal diameter =41mm@ 3 threads per 25mm. Use three-class sealing to seal water to prevent from water leakage. The sealing pressure = 150 psi. Use quick joint to couple the swivel with delivery hose of pump. Nos. 02 iii) Fire hosepipe: Compatible with Pump. 2 inch Flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. Compression resistance is higher than 100 psi. Each one length = 50ft (15 m). With adapter and clamp on each end (male & female), equipped with seal valve and net filter. Nos. 15 iv) Delivery hosepipe: Compatible with swivel & Pump. 2 inch Flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. 25 ft. (7.62m) length with adapter and clamp on each end, Compression resistance is higher than 100 psi. One side use a quick joint to couple the swivel, other side use an adapter and clamp to couple the pump . Nos 04 v) Drilling pipe (Iron made, durable): Compatible with swivel & drilling bit.Overall length, with one end Male & other end Female adapter rigidly joint with the pipe, capable of gentle & easy joint / coupling with other pipe, 10 feet (3.05m). Diameter of main pipe: Outer 1.75 inch (45mm) and inner 1.3 inches (33mm). Adapter size: Male-Length 3 inch (including 2 inch outer thread), compatible & Female-Length 3 inch (inner thread), right hand threaded. Thread per 25mm=3. Socket, inner diameter = 25 mm. Weight- 20kg (?1kg). Nos 05 vi) Bit: Compatible with drilling pipe.Three wing/blade Polycrystalline diamond compact (PDC) triangular drag drilling bit. 4 inch(100 mm) diameter, total length 6 inch(150mm), effective cutting length 4.25inch(110mm) with 4 inch(100mm) transition joint matching (coupling adapter) with drilling pipe. Nos. 04 vii) Pipe wrench: Compatible with drilling pipe, Swivel and bit. Heavy duty 24" (600 mm), steel made, self-cleaning adjustment nut, durable fixed coated grip handle, best quality (welding & soldering able) pipe wrenches. Nos. 12 viii) Tool Box: Standard portable tool box, including compatible tools & accessories. These items are: Set 01 Manual tool box 1 pc Monkey wrench 1 pc Wire cutter 1 pc Air Filter 1 pc Fuel filter 1 pc Screw driver, 300x2x13 1 pc Cross head Screw driver, 200x1.2x8 1 pc Special spanner for centrifugal pump 1 pc Spark plug spanner 1 pc Sparking plug 15 pcs Safety Helmet 04 pcs Rubber shim 06 pcs Sealing ring 06 pcs Head Gazket 15 Pcs B) Top-head automotive rotary mud drilling machine set (DeepRock Hydra-Drill - Model HD2001 or Equivalent): Light weight, convenient to operate, high speed suitable for drilling seismic shot hole in moderately hard Sand, Shale, Clay & Gravel formation. Maximum drilling Depth: 45m (?5m) Weight of any single module should not more than 70 kg. No wheels on tripod. Sets 04 Each Drilling machine set includes following items (Each parts must be Compatible with Top-head automotive rotary mud drilling machine &accessories ) i) Power Head : 6hp or Higher ,4-cycle octane/diesel engine No. 01 ii) Re-circulating Mud pump: Octane/diesel operated engine coupled with centrifugal, narrow type, cast iron made, welding & soldering able pump (nonaluminum) and air cooled type. Suction diameter=75mm, delivery diameter=50mm (Approx.) Pump type :Trash Centrifugal, Self-Priming Engine : OHV gasoline engine Output power: 7 hp or Higher (3600r/min) Displacement: 242 cc or Higher Rated discharge capacity: 1200 to 1500 L/ min Maximum Discharge Capacity: 1500 L/min Suction Head Lift: 8 m Total head lift : 27m Fuel capacity : 6L Dimensions (mm) (LxWxH): 660 x 495 x 515 (Maximum) No. 01 iii) Gear Box : Commercial grade quality, 25:1 gear reduction, more than 315 ft-lbs of torque providing steel gearbox No. 01 iv) Swivel: Compatible with Power head, drilling pipe and delivery hosepipe connecting mud pump. Heavy Steel made long life full flow water course U-type swivel, bent at the middle of the length, compatible with pump delivery hose, easy to joint by clamp with delivery hosepipe & output side compatible(easy to joint by threads) with drill pipe. The internal diameter =41mm@ 3 threads per 25mm. Use three-class sealing to seal water to prevent from water leakage. The sealing pressure at least 150 psi. Use quick joint to couple the swivel with delivery hose of pump. Nos. 02 v) Drilling pipe sized in 5'/1.5 m lengths: Compatible with swivel and drilling bit. Overall length, with one end Male &other end Female adapter rigidly joint with the pipe, capable of gentle & easy joint / coupling with other pipe. Diameter of main pipe: Outer 1.75 inch (45mm) and inner 1.3 inches (33mm). Adapter size: Male-Length 3 inch (including 2 inch outer thread), compatible & Female-Length 3 inch (inner thread), right hand threaded. Thread per 25mm=3. Socket, inner diameter = 25 mm. Weight- 10kg (?1kg). Nos. 20 vi) Bit:Compatible with drilling pipe.Three wing/blade Polycrystalline diamond compact (PDC) triangular drag drilling bit. 4 inch(100 mm) diameter, total length 6 inch(150mm), effective cutting length 4.25inch(110mm) with 4 inch(100mm) transition joint matching (coupling adapter) with drilling pipe. Nos. 04 vii) Delivery hosepipe: Compatible with swivel & Pump. 2 inch Flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. 25 ft. (7.62m) length with adapter and clamp on each end, Compression resistance is higher than 100 psi. One side use a quick joint to couple the swivel, other side use an adapter and clamp to couple the pump. Nos. 04 viii) Fire hosepipe: Compatible with Pump. 2 inch Flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. Compression resistance is higher than 100 psi. Each one length = 50ft (15 m). With adapter and clamp on each end (male & female), equipped with seal valve and net filter. Nos. 15 ix) Pipe wrench: Compatible with drilling pipe, Swivel and bit. Heavy duty 24" (600 mm), steel made, self-cleaning adjustment nut, durable fixed coated grip handle, best quality (welding & soldering able) pipe wrenches. Nos. 12 x) Tool Box: Standard portable tool box, including compatible tools for maintenance of each drilling machine & accessories. Set. 01 xi) Mounting : Tripod round Power Mast Nos. 02 2. 3 KVA Octane Genaretor: 3Phase, 50 Hz, 220 volt with Canopy + ATS System Octane generator, Low noise running, digital control panel, low oil alarm system, automatic voltage regulator. Nos. 05 3 KVADeisel Genaretor: 3Phase, 50 Hz, 220 volt with Canopy + ATS System diesel generator, Low noise running, digital control panel, low oil alarm system, automatic voltage regulator. Nos. 04 3. Delivery hosepipe: Compatible with swivel & drilling engine pump. 2 inch Flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. 26.25 ft. (8m) length with adapter and clamp on each end, Compression resistance is higher than 100 psi. One side use a quick joint to couple the swivel, other side use an adapter and clamp to couple the pump. Nos. 200 4. Fire hosepipe: Compatible with drilling engine pump2 inch flexible heavy duty lay flat rubber hose canvas inside double rubber coated type fiber & wired hose. Compression resistance is higher than 100 psi. Each one length = 65.62ft (20 m). With adapter and clamp on each end (male & female), equipped with seal valve and net filter. Nos. 400 5. Suction hosepipe: Flexible type, transparent plastic fiber & wired hose. Compression resistance is higher than 100 psi. Each one length= 20ft (6.1m). With adapter and clamp on each end (one side to joint with pump & other side with water source), equipped with sit valve and net filter. feet 600 6. Loading Pole: The loading pole is 1-1/4 straight hollow aluminum pole used for placing and compacting explosive charges in bore holes. The aluminum ball need to coupled together with an aluminum socket to connect tamping poles. Ball and socket fittings provide a sturdy connection. Compression resistance is higher than 100 psi. Each one length= 8ft (2.44m). Outer diameter of pole =4 inch Nos. 150 Bangladesh BITAC.PUR.2022-23 GR-39 Lot-03 Procurement of EDM Wire Cut and EDM Drill Machine Bangladesh Supply of Drill Bit (Different Size) Bangladesh Procurement of Lot-II: Mud Chemicals & Completion Fluid Lot- III: Milling Tools & Drill Bits Lot-VII: Bridge Plug and Accessories Bangladesh Sl. No Description Of Goods Unit Quantity Required Remark 1. Die, BJ Clamping for Weatherford Iron Roughneck Model POWERARM 2.1 Positioning Device. Nos. 2. Dies for Weatherford 24-50 auto door back up tong. Nos. 40 3. Brake band for Weatherford 7.6-30 tubing tong Nos. 24 4. Magnate for Weatherford 24-50 casing tong Nos 6 5. 1" Hydraulic Hose 50 ft. long 3000 psi or above wp fitted with Aeroquip Wing Male both ends Union for use with Weatherford Casing tong. Nos. 1 6. 1-1/4" Hydraulic Hose 50 ft. long 600 psi or above wp fitted with Aeroquip Wing Male both ends Union for use with Weatherford Casing Tong Nos. 1 7. 1" Aeroquip Wing type Union set. 3000 psi or above wp with 1" NPT (mal & female) connection. Set 12 8. 1-1/4" Aeroquip Wing Type Union Set, 1000 psi or above wp with 1-1/4" NPT(mal & female) connection. Set. 12 9. 5" Drill Pipe Elevator Center Latch 350T with 18 degree tapered shoulders, safety double latch system to reduce accidental opening. No 2 10. 3 ½" Drill Pipe Elevator Center Latch 250T with 18 degree tapered shoulders, safety double latch system to reduce accidental opening. No 2 11. 2 3/8" Drill Pipe Elevator Center Latch 100T with 18 degree tapered shoulders,safety double latch system to reduce accidental opening. No 1 12. 5? DP Slips medium complete assembly 5? body with Inserts for 5? OD API Drill Pipe No 3 13. 3 ½" DP Slips medium complete assembly 3 ½ inc body with Inserts for 3 ½ OD API Drill Pipe No 2 14. 5? DP Slips Dies (5? body Varco) – 2167- 04 (180 Nos) Set 2 15. Bit sub 3-1/2 IF X 3-1/2 Reg. connection, Float Valve Bore in Reg. connection side. No. 3 16. X-O-S 3-1/2 IF Box X 3-1/2 Reg. pin connection No. 2 17. X-Over 4 1/2” IF box – 3 ½” IF pin No. 3 18. Bit sub 7 5/8 ” reg box – 7 5/8”reg box No. 2 19. Bit sub 6 5/8 ” reg box – 6 5/8”reg box with Float Valve Bore No. 2 20. Bit sub 4 ½” reg box – 4 ½” IF box, Float Valve Bore in Reg. connection side. No. 3 21. Light weight Lifting cap for 5 ?/ 4 ½ " Drill pipe, connection 4 1/2" IF No. 3 22. Lower Kelly Cock, 10000 psi wp, 6.62" OD × 3" ID , Length 22? High Torque Double Shoulder Compatible with API NC 50 (4 ½ IF) box up × pin down connection with metal to metal seal in ball seat and operating port complete with operating key. No. 2 23. 5"OD Threaded Cup Junk Sub / Boot Basket , Cup Length-30", 4-9/16" Cup ID, 1-1/2" Bore for operation in 6 to 6-3/8" Hole with 3-1/2" API Reg. Pin up × Box down connection. No. 3 24. 8-1/4"OD Flat Bottom Junk Mill, Dressed with Crushed sintred tungsten carbide, with a 10" long integral fishing neck with wear pads with 4-1/2" API Reg. Pin connection. Bowen or equivalent. Nos 1 25. 8-1/4"OD Taper Mill (30 degree angle), Dressed with Crushed insert tungsten carbide, with a 10" long integral fishing neck with wear pads with 4-1/2" API Reg. Pin connection. Bowen or equivalent. Nos 1 26. 5-3/4"OD Flat Bottom Junk Mill, Dressed with Crushed sintred tungsten carbide, with a 10" long integral fishing neck with wear pads with 3-1/2" API Reg. Pin connection. Bowen or equivalent. Nos 2 27. 5-3/4"OD Taper Mill (30 degree angle), Dressed with Crushed sintred tungsten carbide, with a 10" long integral fishing neck with wear pads with 3-1/2" API Reg. Pin connection. Bowen or equivalent. Nos 2 28. 4-1/4"OD Flat Bottom Junk Mill, Dressed with Crushed sintred tungsten carbide, with a 10" long integral fishing neck with wear pads with 2-3/8" API Reg. Pin connection. Bowen or equivalent. Nos 1 29. Foldable Runner Treadmill - 6.5HP Motor 0-22 Level Auto Incline - 'Dual Shock 10-Point Absorption System: Now with 'Bluetooth' and The Perfect Running Area: 140 x 48cm (1400 x 480mm), 15.6" LCD Display, Auto Incline, Bluetooth, German made Soft Drop System. DISPLAY: Watch videos on large 10-15.6 inch LCD touch screen display with Wi-Fi | AUDIO: Listen to music on Hi Fi speakers using USB pendrive or audio-in jack | PROGRAMS: 12 preset workout programs & manual mode for customized cardio exercise | PROGRAMS -- There are 12 Pre-Set programs P1-P12 to choose different workouts and manual mode settings of Speed, Distance, Time, Calories & Pulse for customized workouts FOLDABLE: The machine can folded in upright position when not in use. Hydraulic assist system lets you easily lift & lower the treadmill deck Foldable treadmill with cushioned 'Dual Shock 10-Point Absorption System'. Quality assurance & zero defect production rates. Branx Fitness excels in product quality & reliability. Superb 21km/h Max Speed (13mph). CE/ROHS/EN957 & ISO9001 Quality Control Certified & up to GS Standard. Maximumspeed:21kmph No. 3 30. Crystal XP2i digital Pressure gauge (0-15000 psi rated) with Data logger software No. 3 31. HP Laptop Intel Core i7 11th gen GeForce MX450 2GB Graphics 15.6" FHD Anti-glare 1165G7 Processor (12M Cache, 2.80 to 4.70 GHz) 8GB Ram +1TB HDD, or upgrade . No 4 32. Micromotion Coriolis Mass Flowmeter F300 series No. 1 33. Micromotion 2700 Multiple Variable Flow Transmitter with remote mounting No. 1 34. Micromotion Prolink III software No. 1 35. Nuflo Turbine 1502 Weco union liquid turbine meter or equivalent mounted on 2” cementing line with remote data acquisition system/software No. 1 36. 1502 Weco Hammer Union Pressure Transmitter- mounted on 2” cementing line (Rosemount/Viatran or equivalent, 0-15000 psi rated) with remote data acquisition system/software No. 1 For Cement Silo No. 37. 4” Butterfly Valve No. 10 38. 3” non-return Valve No. 5 39. 1” non-return valve No. 20 40. 4” discharge hose, 25-30 ft long c/w 4” opposite fig 100 hammer union male x female connection, WP= 150 psi No. 10 41. 3” air hose, 25-30 ft long c/w 3” opposite fig 100 hammer union male x female connection, WP= 150 psi No. 6 42. 1” rubber hose NPT connection 300 psi, 4 ft No. 25 43. 1” Tee No. 25 44. 1” socket No. 25 45. 1” nipple No. 25 46. 1” Air jet nipple with 1” aeration hose & 1” check valve No. 20 Bangladesh APSCL/Pro-19/e-gp/WSN/2021-2022/GRLWSN-009 Procurement of a bench lathe, bench milling machine and portable drill bit grinder for Workshop Division, Ashuganj 450MW CCPP(North), APSCL. Bangladesh Buying of Drill Bit (Different Size) Bangladesh
No. 12, 1 st floor, Block B2, EGS Business Park, World Trade Center,
Bakirkoy - Istanbul - Turkey